sanken electric co., ltd. http://www.sanken-ele.co.jp/en/ description the SHV-02JN is a 1000 v silicon rectifier diode, which can sustain a high voltage with low loss. high voltage rectifier diode not to scale SHV-02JN shv02jn-ds december 11, 2007 package: axial features and benefits ? high peak reverse voltage, v rm : 1.0 kv ? low forward voltage, v f : 2.0 v (max.) at i f = 10 ma ? peak forward surge current, i fsm : 3 a ? average forward current, i f(av) : 30 ma ? flammability rating ul94v-0 (equivalent) ? pins pb (lead) free application ? automobile ignition coil start-up voltage surge arrester product structure epoxy resin body application overmolding silver plated copper wire pins
2 sanken electric co., ltd. shv02jn-ds high voltage rectifier diode SHV-02JN december 11, 2007 absolute maximum ratings characteristic symbol conditions rating unit peak reverse voltage v rm 1.0 kv peak reverse surge current i rsm half value width: 100 s triangular wave, peak value, one shot 30 ma average forward current i f(av) 50 hz, half sine wave, average value 30 ma peak forward surge current i fsm 50 hz, half sine wave, one shot 3 a junction temperature t j ?40 to 150 c storage temperature t stg ?40 to 150 c electrical characteristics valid at t a = 25c, unless otherwise specified characteristic symbol test conditions value unit forward voltage v f i f = 10 ma 2.0 (max) v reverse current i r v r = v rm 10 (max) a reverse breakdown voltage v z i r = 100 a 1.1 to 2.0 kv selection guide part number packing SHV-02JNv1 5000 pieces per reel
3 sanken electric co., ltd. shv02jn-ds high voltage rectifier diode SHV-02JN december 11, 2007 c = 25 pf f igniter v test = 16 v i r(peak) = 50 ma 60 s 0 a i r i f l f igniter v test = 16 v electrical operation tests ambient temperature, t a : 130c capacitance: c: 25 pf 1) f = 66 hz for 3 minutes 2) f = 33.3 hz for 20 hours ambient temperature, t a : 130c secondary discharge voltage: 25 5 kv l: 600 mm maximum f = 66.6 hz t = 1000 hours pulse width : 60 s peak value: 50 ma power per pulse: 5.4 mj test condition test condition reverse current waveform through diode spark discharge test the ratings in the electrical characteristics must be satisfied after tests at the following condition open operation test the ratings in the electrical characteristics must be satisfied after tests at the following condition note: additional conditions during electrical operation tests in this page 1. sample diode should be overmolded with more than 10 mm 10 mm 30 mm of epoxy resin, but thermal resistance, r th(j-a) , at 1 w dissipation less than 65/w. 2. if product high-voltage code is not specified, no line noise resistance is specified.
4 sanken electric co., ltd. shv02jn-ds high voltage rectifier diode SHV-02JN december 11, 2007 ymd pin treatment pb-free. device composition compliant with the rohs directive. cathode index band package outline package marking 6.50.2 2 1 27 min 27 min +0.01 ?0.02 ? 0.5 cathode index band dimensions in mm pin dimension does not include trim burr ?2.500.2 the body is intentionally small, with the expectation that the product will be overmolded in the application where used. for this reason, the use of the diode is not recommended unless it is overmolded. overmolding is required to insure insulation against voltage at the surface, heat dissipation, and to protect against penetration of moisture. an epoxy resin should be used for the overmolding. it must have superior adhesion to the surface of the product body, thermal conduction, protection against penetration of moisture, and must have low distortion when expanding and contracting while the product is being used in the application. material composition and internal structure caution for use 1 2 lot number y is the last digit of the year (0 to 9) m is the month (1 to 9, o, n, d) d is the period of days a ? 1st to 10th b ? 11th to 20th c ? 21st to 31st marking repeats on far side type mark 1. body: plastic, epoxy resin 2. pins: cu wire ag plated
5 sanken electric co., ltd. shv02jn-ds high voltage rectifier diode SHV-02JN december 11, 2007 ? the contents in this document are subject to changes, for improvement and other purposes, without notice. make sure that this is the latest revision of the document before use. ? application and operation examples described in this document are quoted for the sole purpose of reference for the use of the prod- ucts herein and sanken can assume no responsibility for any infringement of industrial property rights, intellectual property r ights or any other rights of sanken or any third party which may result from its use. ? although sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of se micon- ductor products at a certain rate is inevitable. users of sanken products are requested to take, at their own risk, preventativ e measures including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device failure or malfunction. ? sanken products listed in this document are designed and intended for the use as components in general purpose electronic equ ip- ment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). when considering the use of sanken products in the applications where higher reliability is required (transportation equipment and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), and whenever long life expectancy is required even in general purpose electronic equipment or apparatus, please contact your nearest sanken sales representative to discuss, prior to the use of the products herein. the use of sanken products without the written consent of sanken in the applications where extremely high reliability is requi red (aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited. ? in the case that you use sanken products or design your products by using sanken products, the reliability largely depends on the degree of derating to be made to the rated values. derating may be interpreted as a case that an operation range is set by dera ting the load from each rated value or surge voltage or noise is considered for derating in order to assure or improve the reliability. in general, derating factors include electric stresses such as electric voltage, electric current, electric power etc., environmental stres ses such as ambient temperature, humidity etc. and thermal stress caused due to self-heating of semiconductor products. for these stress es, instantaneous values, maximum values and minimum values must be taken into consideration. in addition, it should be noted that since power devices or ic's including power devices have large self-heating value, the de gree of derating of junction temperature affects the reliability significantly. ? when using the products specified herein by either (i) combining other products or materials therewith or (ii) physically, ch emically or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance and proceed therewith at your own responsibility. ? anti radioactive ray design is not considered for the products listed herein. ? sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of sanken's dis tribu- tion network. ? the contents in this document must not be transcribed or copied without sanken's written consent.
|
